TEM-560P PCMCIA

TRENDWARE INTERNATIONAL

TEM-560P PCMCIA

Card Type

Modem, Fax

Chip Set

Unidentified

Maximum Modem Rate

33.6Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation Protocol

Bell 103A/212A

ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34, V.34bis, K56flex

Fax Modulation Protocol

ITU-T V.17, V.21CH2, V.27ter, V.29

Error Correction/Compression

MNP5, V.42, V.42bis

Fax Class

Class I

Data Bus

PCMCIA

54928

SUPPORTED COMMAND SET

Basic AT Commands

AT, A/

A, E, H, M, P, Q, T, V, W

&C, &F, &G, &V, &Z

Extended AT Commands

\J, \T, \V

Special Commands

-C

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S30

Note: See MHI Help File for full command documentation.

Proprietary AT Command Set

COMMUNICATION PROTOCOLS

Type:

Configuration

Format:

AT [cmds] Bn [cmds]

Description:

Selects the communication protocol for data calls

Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols.

Command

Protocol

B0

ITU-T V.22 at 1200bps

B1

Bell 212A at 1200bps

B2

V.23 at 1200/75bps

B3

V.23 at 75/1200bps

B15

V.21 at 300bps

B16

Bell 103 at 300bps

DIAL

Type:

Immediate

Format:

AT [cmds] D<#> [cmds]

Description:

Dials telephone number according to any modifiers included in the string

Note:

Any combination of modifiers can be used to produce the desired dial functions in sequence.

Command

Function

DL

Re-dial last number

DP

Pulse dialing enabled

DR

Answer mode enabled; originate mode disabled following handshake initiation.

DS=n

Dial stored telephone number n

DT

Tone dialing enabled/Pulse dialing disabled

DW

Dialing resumed following dial tone detection

D,

Dialing paused for amount of time specified in S8 register

D!

Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.

D@

Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.

D;

Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

AUTO-MODE DETECTION

Type:

Configuration

Format:

AT [cmds] Nn [cmds]

Description:

Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.

Command

Function

N0

Auto-mode detection disabled

í N1

In originate mode, handshake begins at line speed designated by the S37 register. Modem can shift to a slower speed if necessary.

In answer mode, handshake attempted with the following protocols in order - V.FC, V.32bis, V.32, V.22bis, V.22 or Bell 212, V.21, and Bell 103

ON-LINE

Type:

Immediate

Format:

AT [cmds] On [cmds]

Description:

Controls on-line command (data transmission) state options.

Note: The O command must be placed at the end of the command string.

Command

Function

O0

On-line command mode with no retraining enabled

O1

On-line command mode with retraining enabled

O3

Issue a rate re-negotiate, then return to on-line state

SELECT CALL PROGRESS RESULT CODES

Type:

Configuration

Format:

AT [cmds] Xn [cmds]

Description:

Enables selection of tone detection and associated result code format options

Command

Function

X0

Busy and dial tone detection disabled; result codes 0 - 4 enabled.

X1

Busy and dial tone detection disabled; result codes 0 - 5 & 10 enabled.

X2

Busy tone detection disabled, dial tone detection enabled; result codes 0 - 6 & 10 enabled.

X3

Busy tone detection enabled, dial tone detection disabled; result codes 0 - 5, 7 & 10 enabled.

í X4

Busy and dial tone detection enabled; result codes 0 - 7 & 10 enabled.

X5

Busy and dial tone detection enabled; result codes 0 - 7 & 10 enabled.

X6

Busy and dial tone detection enabled; result codes 0 - 7 & 10 enabled.

X7

Display CONNECT or "1" for all speeds. Check dial tone and busy tone

SOFT RESET

Type:

Immediate

Format:

AT [cmds] Zn [cmds]

Description:

Restores modem profiles previously saved in non-volatile RAM using the &W command.

Command

Function

Z0

Restore setting 0

Z1

Restore setting 0

DATA TERMINAL READY (DTR)

Type:

Configuration

Format:

AT [cmds] &Dn [cmds]

Description:

Selects modem response to DTR

Note: The action each variant of &D causes depends on the setting of &Q

Command

Function

í &D0

Modem does not respond to DTR

&D1

Modem goes to command mode after DTR goes is off

&D2

Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled.

&D3

Modem is initialized after DTR goes off

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] &Kn [cmds]

Description:

Enables flow control options

Command

Function

&K0

Flow control disabled

í &K3

RTS/CTS flow control enabled

&K4

XON/XOFF flow control enabled

PULSE DIALING RATIO

Type:

Configuration

Format:

AT [cmds] &Pn [cmds]

Description:

Selects pulse dial make/break ratio

Command

Function

í &P0

39/61ms at 10pps (North America)

&P1

33/67ms at 10pps (Europe)

COMMUNICATIONS MODE

Type:

Configuration

Format:

AT [cmds] &Qn [cmds]

Description:

Selects communications mode options

Command

Mode

í &Q0

Buffered asynchronous mode, serial port speed follows connect speed.

&Q5

Error correction mode

&Q8

MNP error control mode

&Q9

V.42 or MNP error control mode

DATA SET READY (DSR)

Type:

Configuration

Format:

AT [cmds] &Sn [cmds]

Description:

Selects DSR options

Command

Function

&S0

DSR forced high

í &S1

DSR high only while modem is handshaking or connected

TEST MODES

Type:

Immediate

Format:

AT [cmds] &Tn

Description:

Selects test options

Command

Function

&T0

End current test

&T1

Begin local analog loopback test

&T3

Begin local digital loopback

&T6

Request remote digital loopback

STORE ACTIVE PROFILE

Type:

Configuration

Format:

AT [cmds] &Wn [cmds]

Description:

Writes the values for the active profile into the non-volatile RAM

Extended AT Commands

CONNECT MODE

Type:

Configuration

Format:

AT [cmds] \Nn [cmds]

Description:

Controls the type of connection the modem will operate in

Command

Function

\N0

Normal mode enabled

\N1

Direct mode enabled

\N2

Reliable mode enabled

\N3

Auto-reliable mode enabled

\N4

V.42 reliable mode enabled

FLOW CONTROL TYPE

Type:

Configuration

Format:

AT [cmds] \Qn [cmds]

Description:

Sets type of flow control used by modem

Command

Function

\Q0

Flow control disabled

\Q1

Bidirectional XON/XOFF flow control enabled

\Q3

Bidirectional RTS/CTS flow control enabled

BLACKLIST

Type:

Configuration

Format:

AT [cmds] %Bn [cmds]

Description:

View numbers in blacklist

COMPRESSION

Type:

Configuration

Format:

AT [cmds] %Cn [cmds]

Description:

Selects data compression

Command

Function

%C0

Data compression disabled

%C1

V.42bis/MNP5 enabled

S(status) -REGISTERS

V.34 MODULATION

Format

AT [cmds] S28=n [cmds]

Default:

1

Range:

0-255

Description:

Controls the V.34 modulation

Command

Function

S28=0

Disabled

S28=1-255

Enabled

ERROR CORRECTION NEGOTIATION

Type:

Register

Format

AT [cmds] S36=n [cmds]

Description:

Selects the action of the modem if it fails to connect with the error-correction protocol set in &Q.

Command

Function

S36=0, 2

Hang up

S36=1, 3

Attempt a direct connection

S36=4, 6

Attempt a connection at MNP2-4; if that fails, hang up.

S36=5, 7

Attempt a connection at MNP2-4; if that fails, attempt a direct connection.

DCE LINE SPEED

Type:

Register

Format

AT [cmds] S37=n [cmds]

Description:

Sets the maximum allowable data exchange rate attempted during handshake process.

Command

Function

í S37=0

Maximum modem speed

S37=2

1200/75bps

S37=3

300bps

S37=5

1200bps

S37=6

2400bps

S37=7

4800bps

S37=8

7200bps

S37=9

9600bps

S37=10

12000bps

S37=11

14400bps

S37=12

16800bps

S37=13

19200bps

S37=14

21600bps

S37=15

24000bps

S37=16

26400bps

S37=17

28800bps

S37=18

31200bps

S37=19

33600bps

DIAL LINE RATE

Type:

Register

Format

AT [cmds] S38=n [cmds]

Description:

56K dial line rate selection

Command

Function

í S38=0

56K disabled

S38=1

56K enabled, auto-speed selection, maximum modem speed

S38=2

32000bps

S38=3

34000bps

S38=4

36000bps

S38=5

38000bps

S38=6

40000bps

S38=7

42000bps

S38=8

44000bps

S38=9

46000bps

S38=10

48000bps

S38=11

50000bps

S38=12

52000bps

S38=13

54000bps

S38=14

56000bps

SLEEP TIMER

Type:

Register

Format

AT [cmds] S89 [cmds]

Range:

0 - 60

Unit:

1 second

Description:

Sleep mode control timer

Command

Function

0

Disable sleep mode

5 - 60

Number of seconds of inactivity before entering sleep mode

TRANSMISSION LEVEL (JAPANESE VERSION ONLY)

Type

Register or Configuration

Format

AT [cmds] S91=n [cmds]

Default

14

Range

6 - 15

Unit

-1 dBm

Description

Sets the signal level for transmission over leased-lines

FEATURE NEGOTIATION OPTIONS

Type:

Register

Format:

AT [cmds] S48=n [cmds]

Description:

Selects active error correction and compression protocols

Command

Function

S48=7

Detection negotiation and XID negotiation enabled

S48=128

Fall-back to options set in S36

Card Type	Modem, Fax
Chip Set	Unidentified
Maximum Modem Rate	33.6Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation Protocol	Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34, V.34bis, K56flex
Fax Modulation Protocol	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, V.42, V.42bis
Fax Class	Class I
Data Bus	PCMCIA

COMMUNICATION PROTOCOLS
Type:	Configuration
Format:	AT [cmds] Bn [cmds]
Description:	Selects the communication protocol for data calls
Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols.
Command	Protocol
B0	ITU-T V.22 at 1200bps
B1	Bell 212A at 1200bps
B2	V.23 at 1200/75bps
B3	V.23 at 75/1200bps
B15	V.21 at 300bps
B16	Bell 103 at 300bps

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials telephone number according to any modifiers included in the string
Note:	Any combination of modifiers can be used to produce the desired dial functions in sequence.
Command	Function
DL	Re-dial last number
DP	Pulse dialing enabled
DR	Answer mode enabled; originate mode disabled following handshake initiation.
DS=n	Dial stored telephone number n
DT	Tone dialing enabled/Pulse dialing disabled
DW	Dialing resumed following dial tone detection
D,	Dialing paused for amount of time specified in S8 register
D!	Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.
D@	Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.
D;	Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

AUTO-MODE DETECTION
Type:	Configuration
Format:	AT [cmds] Nn [cmds]
Description:	Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.
Command	Function
N0	Auto-mode detection disabled
í N1	In originate mode, handshake begins at line speed designated by the S37 register. Modem can shift to a slower speed if necessary. In answer mode, handshake attempted with the following protocols in order - V.FC, V.32bis, V.32, V.22bis, V.22 or Bell 212, V.21, and Bell 103

ON-LINE
Type:	Immediate
Format:	AT [cmds] On [cmds]
Description:	Controls on-line command (data transmission) state options.
Note: The O command must be placed at the end of the command string.
Command	Function
O0	On-line command mode with no retraining enabled
O1	On-line command mode with retraining enabled
O3	Issue a rate re-negotiate, then return to on-line state

SELECT CALL PROGRESS RESULT CODES
Type:	Configuration
Format:	AT [cmds] Xn [cmds]
Description:	Enables selection of tone detection and associated result code format options
Command	Function
X0	Busy and dial tone detection disabled; result codes 0 - 4 enabled.
X1	Busy and dial tone detection disabled; result codes 0 - 5 & 10 enabled.
X2	Busy tone detection disabled, dial tone detection enabled; result codes 0 - 6 & 10 enabled.
X3	Busy tone detection enabled, dial tone detection disabled; result codes 0 - 5, 7 & 10 enabled.
í X4	Busy and dial tone detection enabled; result codes 0 - 7 & 10 enabled.
X5	Busy and dial tone detection enabled; result codes 0 - 7 & 10 enabled.
X6	Busy and dial tone detection enabled; result codes 0 - 7 & 10 enabled.
X7	Display CONNECT or "1" for all speeds. Check dial tone and busy tone

SOFT RESET
Type:	Immediate
Format:	AT [cmds] Zn [cmds]
Description:	Restores modem profiles previously saved in non-volatile RAM using the &W command.
Command	Function
Z0	Restore setting 0
Z1	Restore setting 0

DATA TERMINAL READY (DTR)
Type:	Configuration
Format:	AT [cmds] &Dn [cmds]
Description:	Selects modem response to DTR
Note: The action each variant of &D causes depends on the setting of &Q
Command	Function
í &D0	Modem does not respond to DTR
&D1	Modem goes to command mode after DTR goes is off
&D2	Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled.
&D3	Modem is initialized after DTR goes off

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] &Kn [cmds]
Description:	Enables flow control options
Command	Function
&K0	Flow control disabled
í &K3	RTS/CTS flow control enabled
&K4	XON/XOFF flow control enabled

PULSE DIALING RATIO
Type:	Configuration
Format:	AT [cmds] &Pn [cmds]
Description:	Selects pulse dial make/break ratio
Command	Function
í &P0	39/61ms at 10pps (North America)
&P1	33/67ms at 10pps (Europe)

COMMUNICATIONS MODE
Type:	Configuration
Format:	AT [cmds] &Qn [cmds]
Description:	Selects communications mode options
Command	Mode
í &Q0	Buffered asynchronous mode, serial port speed follows connect speed.
&Q5	Error correction mode
&Q8	MNP error control mode
&Q9	V.42 or MNP error control mode

DATA SET READY (DSR)
Type:	Configuration
Format:	AT [cmds] &Sn [cmds]
Description:	Selects DSR options
Command	Function
&S0	DSR forced high
í &S1	DSR high only while modem is handshaking or connected

TEST MODES
Type:	Immediate
Format:	AT [cmds] &Tn
Description:	Selects test options
Command	Function
&T0	End current test
&T1	Begin local analog loopback test
&T3	Begin local digital loopback
&T6	Request remote digital loopback

STORE ACTIVE PROFILE
Type:	Configuration
Format:	AT [cmds] &Wn [cmds]
Description:	Writes the values for the active profile into the non-volatile RAM

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Description:	Controls the type of connection the modem will operate in
Command	Function
\N0	Normal mode enabled
\N1	Direct mode enabled
\N2	Reliable mode enabled
\N3	Auto-reliable mode enabled
\N4	V.42 reliable mode enabled

FLOW CONTROL TYPE
Type:	Configuration
Format:	AT [cmds] \Qn [cmds]
Description:	Sets type of flow control used by modem
Command	Function
\Q0	Flow control disabled
\Q1	Bidirectional XON/XOFF flow control enabled
\Q3	Bidirectional RTS/CTS flow control enabled

BLACKLIST
Type:	Configuration
Format:	AT [cmds] %Bn [cmds]
Description:	View numbers in blacklist

COMPRESSION
Type:	Configuration
Format:	AT [cmds] %Cn [cmds]
Description:	Selects data compression
Command	Function
%C0	Data compression disabled
%C1	V.42bis/MNP5 enabled

V.34 MODULATION
Format	AT [cmds] S28=n [cmds]
Default:	1
Range:	0-255
Description:	Controls the V.34 modulation
Command	Function
S28=0	Disabled
S28=1-255	Enabled

ERROR CORRECTION NEGOTIATION
Type:	Register
Format	AT [cmds] S36=n [cmds]
Description:	Selects the action of the modem if it fails to connect with the error-correction protocol set in &Q.
Command	Function
S36=0, 2	Hang up
S36=1, 3	Attempt a direct connection
S36=4, 6	Attempt a connection at MNP2-4; if that fails, hang up.
S36=5, 7	Attempt a connection at MNP2-4; if that fails, attempt a direct connection.

DCE LINE SPEED
Type:	Register
Format	AT [cmds] S37=n [cmds]
Description:	Sets the maximum allowable data exchange rate attempted during handshake process.
Command	Function
í S37=0	Maximum modem speed
S37=2	1200/75bps
S37=3	300bps
S37=5	1200bps
S37=6	2400bps
S37=7	4800bps
S37=8	7200bps
S37=9	9600bps
S37=10	12000bps
S37=11	14400bps
S37=12	16800bps
S37=13	19200bps
S37=14	21600bps
S37=15	24000bps
S37=16	26400bps
S37=17	28800bps
S37=18	31200bps
S37=19	33600bps

DIAL LINE RATE
Type:		Register
Format		AT [cmds] S38=n [cmds]
Description:		56K dial line rate selection
Command	Function
í S38=0	56K disabled
S38=1	56K enabled, auto-speed selection, maximum modem speed
S38=2	32000bps
S38=3	34000bps
S38=4	36000bps
S38=5	38000bps
S38=6	40000bps
S38=7	42000bps
S38=8	44000bps
S38=9	46000bps
S38=10	48000bps
S38=11	50000bps
S38=12	52000bps
S38=13	54000bps
S38=14	56000bps

SLEEP TIMER
Type:	Register
Format	AT [cmds] S89 [cmds]
Range:	0 - 60
Unit:	1 second
Description:	Sleep mode control timer
Command	Function
0	Disable sleep mode
5 - 60	Number of seconds of inactivity before entering sleep mode

TRANSMISSION LEVEL (JAPANESE VERSION ONLY)
Type	Register or Configuration
Format	AT [cmds] S91=n [cmds]
Default	14
Range	6 - 15
Unit	-1 dBm
Description	Sets the signal level for transmission over leased-lines

FEATURE NEGOTIATION OPTIONS
Type:			Register
Format:	AT [cmds] S48=n [cmds]
Description:	Selects active error correction and compression protocols
Command		Function
S48=7		Detection negotiation and XID negotiation enabled
S48=128		Fall-back to options set in S36