Card Type	Fax, Modem (synchronous/asynchronous)
Chip Set	Unidentified
Maximum Data Rate	28.8Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	External
Fax Class	Class I & II
Data Modulation Protocol	Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34
Fax Modulation Protocol	ITU-T V.17, V.21CH2, V.27ter, V.29, V.33
Error Correction/Compression	MNP5, MNP10, V.42, V.42bis

CONNECTIONS
Function	Label		Function		Label
Line in		CN1		RS-232/422		CN3
Line out		CN2		DC power		CN4

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
MR	Red	On	Modem is ready
MR	Red	Off	Self-test failed
MR	Red	Blinking	Self-test in progress
HS	Red	On	Modem is operating at highest speed available
HS	Red	Off	Modem is operating at slower speed available
AA	Red	On	Auto-answer enabled
AA	Red	Off	Auto-answer disabled
CD	Red	On	Carrier signal detected
CD	Red	Off	Carrier signal not detected
OH	Red	On	Modem is off-hook
OH	Red	Off	Modem is on-hook
SD	Red	On	Modem is transmitting data
SD	Red	Off	Modem is not transmitting data
RD	Red	On	Modem is receiving data
RD	Red	Off	Modem is not receiving data
TR	Red	On	DTR signal is high
TR	Red	Off	DTR signal is low
PWR	Red	On	Power is on
PWR	Red	Off	Power is off

AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD
Type:	Configuration
Format:	AT [cmds] %En [cmds]
Description:	Controls auto-retrain mode and fallback/fall-forward
Command	Function
í %E0	Auto-retrain disabled
%E1	Auto-retrain enabled
í %E2	Auto-fallback/fall-forward enabled

BIT MAPPED REGISTERS
Register	Default
S14	138
S16	0
S21	4
S22	117
S23	55
S27	73
S28	0
S31	2
S39	3
S40	105
S41	3
S201	58

BREAK SEND
Type:	Configuration
Format:	AT [cmds] \Bn [cmds]
Default:	3
Range:	1-9
Unit:	.1 second
Description:	Sends break to modem

BREAK TYPE
Type:		Configuration
Format:		AT [cmds] \Kn [cmds]
Description:		Configures action of break signal
Command	Break from DTE		Modem receives \B	Break received from remote modem
\K0	Online command mode enabled, send no break to remote modem		Break sent to remote modem and buffered cleared	Buffers cleared, break sent to DTE
\K1	Break sent to remote modem and buffered cleared		Break sent to remote modem and buffered cleared	Buffers cleared, break sent to DTE
\K2	Online command mode enabled, send no break to remote modem		Send break to remote modem immediately	Break sent immediately to DTE
\K3	Send break to remote modem immediately		Send break to remote modem immediately	Break sent immediately to DTE
\K4	Online command mode enabled, send no break to remote modem		Send break with transmitted data	Break sent with received data to the DTE
í \K5	Send break with transmitted data		Send break with transmitted data	Break sent with received data to the DTE

COMPRESSION
Type:	Configuration
Format:	AT [cmds] %Cn [cmds]
Description:	Selects data compression
Command	Function
%C0	Data compression disabled
%C1	MNP5 enabled
%C2	V.42bis enabled
í %C3	MNP5 and V.42bis enabled

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Description:	Controls the type of connection the modem will operate in
Command	Function
\N0	Normal mode enabled
\N1	Direct mode enabled
\N2	Reliable mode enabled
\N3	Auto-reliable mode enabled
\N4	V.42 reliable mode enabled
\N5	MNP auto-reliable mode enabled

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials telephone number according to any modifiers included in the string
Note:	Any combination of modifiers can be used to produce the desired dial functions in sequence.
Modifier	Function
L	Re-dial last number
P	Pulse dialing enabled
R	Accepted but not acted upon
S=n	Dial stored telephone number n
T	Tone dialing enabled
W	Dialing resumed following dial tone detection
*	Dials the ‘Star’ digit
#	Dials the ‘Gate’ digit
!	Modem commanded to go off-hook for specified time before returning on-hook
@	Wait for quiet answer
&	Waits for prompt tone for amount of time specified by the S7 register
,	Dialing paused for amount of time specified in S8 register
;	Modem returned to command state after dialing
^	Disable calling tone
>	Country specific, generates grounding pulse

FLASH DIAL MODIFIER TIME
Type:	Register
Format	AT [cmds] S29=n [cmds]
Default:	0
Range:	0-255
Unit:	.01 second
Description:	Time the modem will go on-hook upon receiving the ! dial modifier in dial string.

FLOW CONTROL CHARACTER - XOFF
Type:	Register
Format:	AT [cmds] S33=n [cmds]
Default:	19
Range:	0-255
Unit:	ASCII
Description:	Sets the character used to represent XOFF

FLOW CONTROL CHARACTER - XON
Type:	Register
Format:	AT [cmds] S32=n [cmds]
Default:	17
Range:	0-255
Unit:	ASCII
Description:	Sets the character used to represent XON

INACTIVITY TIMER
Type:	Register
Format	AT [cmds] S30=n [cmds]
Default:	0
Range:	0-255
Unit:	10 seconds
Description:	Maximum duration of DTE and DCE inactivity allowed prior to initiating hang-up process.

LINE SIGNAL LEVEL
Type:	Immediate
Format:	AT [cmds] %L [cmds]
Description:	Returns a value which indicates the received line signal level in -dBm

LINE SIGNAL QUALITY
Type:	Immediate
Format:	AT [cmds] %Q [cmds]
Description:	Returns a value which indicates line signal quality

MAXIMUM BLOCK SIZE FOR TRANSMISSION
Type:	Configuration
Format:	AT [cmds] \An [cmds]
Description:	Sets the maximum transmittable block size
Command	Function
\A0	MNP block size is 64 characters
í \A1	MNP block size is 128 characters
\A2	MNP block size is 192 characters
\A3	MNP block size is 256 characters

MNP - EXTENDED SERVICES
Type:	Configuration
Format:	AT [cmds] -Kn [cmds]
Description:	Selects MNP extended services
Command	Function
-K0	MNP extended services disabled
-K1	MNP extended services enabled
-K2	MNP extended services enabled without indicating MNP on the answer detection phase.

MNP10 - FALLBACK
Type:	Configuration
Format:	AT [cmds] -Qn [cmds]
Description:	Allows MNP10 to fall back to speeds slower than 4800bps
Command	Function
-Q0	MNP10 at 2400 and 1200bps disabled
í -Q1	MNP10 at 2400 and 1200bps enabled

MNP10 - LINK NEGOTIATION
Type:	Configuration
Format:	AT [cmds] *Hn [cmds]
Description:	Sets the speed at which MNP10 link negotiation will occur
Command	Function
í *H0	Link will be negotiated at highest possible speed
*H1	Link will be negotiated at 1200bps
*H2	Link will be negotiated at 4800bps

MNP10 - POWER LEVEL ADJUST
Type:	Configuration
Format:	AT [cmds] )Mn [cmds]
Description:	Controls automatic transmit power level adjustment during MNP 10 link negotiation
Command	Function
í )M0	Power level adjustment disabled
)M1	Power level adjustment enabled, power level determined by modem
)M2	Power level adjustment enabled, power level remains fixed

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports product code
I1	Reports ROM checksum
I2	Reports ROM checksum
I3	Reports product revision code
I4	Reports product ID
I5	Reports country code
I6	Reports modem data pump version number
I7	Reports DAA code from MCU interrogation

SLEEP TIMER
Type:	Register
Format	AT [cmds] S24=n [cmds]
Default:	0
Range:	0-255
Unit:	1 second
Description:	Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode.

TRANSMISSION LEVEL - CELLULAR
Type:	Configuration
Format:	AT [cmds] @Mn [cmds]
Default:	0
Range:	11-31
Unit:	-1dBm
Description:	Sets the signal level for transmission while in cellular mode
Command	Function
@M0	-26 dBm
@M1	-30 dBm
@M2-@M10	-10 dBm

TRANSMISSION LEVEL - FAX
Type:	Register
Format:	AT [cmds] S92=n [cmds]
Default:	10
Range:	0-15
Unit:	-1 dBm
Description:	Sets the signal level for transmission while in fax mode

TRANSMISSION LEVEL - PSTN
Type	Register or Configuration
Format	AT [cmds] S91=n [cmds]
Default	10
Range	0-15
Unit	-1 dBm
Description	Sets the signal level for transmission over PSTN

V.32 - COMPROMISE EQUALIZER
Type:	Configuration
Format:	AT [cmds] :En [cmds]
Description:	Controls V.32 compromise equalizer
Command	Function
:E0	Equalizer disabled
í :E1	Equalizer enabled