MAXTECH CORPORATION
XPV 336IC (SF-1133HV/C3)
|
Card Type |
Modem/Fax card |
|
Chip Set |
Unidentified |
|
I/O Options |
Line in(RJ-11), line out(RJ-11), microphone jack, speaker jack |
|
Maximum Modem Rate |
33.6Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation Protocol |
Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V34, V34+, V.FC |
|
Fax Modulation Protocol |
ITU-T V.17, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
Fax Class |
Class I |
|
Data Bus |
16-bit ISA |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
RJ-11 line |
CN1 |
Microphone |
CN3 | |||
|
RJ-11 line |
CN2 |
Speaker |
CN4 | |||
|
USER CONFIGURABLE SETTINGS | ||
|
Setting |
Label |
Position |
|
í Stereo speaker configuration enabled |
JP5 |
Closed |
|
Mono speaker configuration enabled |
JP5 |
Open |
|
SERIAL PORT ADDRESS | ||||
|
Setting |
S1/A |
S1/B |
S1/C |
S1/D |
|
COM1 (3F8h) |
Open |
Open |
Closed |
Closed |
|
COM2 (2F8h) |
Closed |
Open |
Open |
Closed |
|
COM3 (3E8h) |
Open |
Closed |
Closed |
Open |
|
COM4 (2E8h) |
Closed |
Closed |
Open |
Open |
|
í Plug & Play enabled |
Open |
Open |
Open |
Open |
|
INTERRUPT | |||||||
|
Setting |
S2/A |
S2/B |
S2/C |
S2/D |
S2/E |
S2/F |
S2/G |
|
IRQ3 |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
|
IRQ4 |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
|
IRQ5 |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
|
IRQ7 |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
|
IRQ10 |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
|
IRQ11 |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
|
IRQ12 |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
|
í Plug & Play enabled |
Closed |
Closed |
Closed |
Closed |
Closed |
Closed |
Closed |
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, +++, A/ |
|
A, E, H, M, O, P, Q, T, V, X, Y, Z |
|
&C, &F, &G, &W, &Y, &Z |
|
Extended AT Commands |
|
\A, \B, \C, \G, \J, \K, \O, \U, \X, \Y, \Z |
|
%A, %G |
|
-J |
|
"H |
|
S Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, |
|
S23, S25, S27, S30, S31, S33, S37 |
|
Special Commands |
|
+MS |
|
Note: See MHI Help File for full command documentation. |
PROPRIETARY AT COMMAND SET
|
AUTO-MODE DETECTION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Nn [cmds] |
|
Description: |
Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. |
|
Command |
Function |
|
N0 |
When originating or answering; handshake only at DTE to modem rate |
|
í N1 |
When originating or answering; handshake at DTE to modem rate. Modem can shift to a lower speed if necessary |
|
AUXILIARY RELAY | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Jn [cmds] |
|
Description: |
Enables/disables auxiliary relay |
|
Command |
Jack Type |
|
&J0 |
Auxiliary relay disabled |
|
&J1 |
Auxiliary relay enabled when modem is off-hook |
|
COMMUNICATION PROTOCOLS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Bn [cmds] |
|
Description: |
Selects the communication protocol for data calls |
Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols. | |
|
Command |
Protocol |
|
B0 |
CCITT mode |
|
B1 |
Bell 212A at 300 or 1200bps |
|
B2 |
V.23 at 1200bps transmit, 75bps receive |
|
B3 |
V.23 at 75bps transmit, 1200bps receive |
|
COMMUNICATIONS MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Mn [cmds] |
|
Description: |
Selects communications mode |
|
Command |
Mode |
|
&M0 |
Asynchronous mode |
|
COMMUNICATIONS MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Qn [cmds] |
|
Description: |
Selects communications mode options |
|
Command |
Mode |
|
&Q0 |
Asynchronous mode, serial port speed follows connect speed. |
|
CONFIGURATION PROFILES | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] &Vn [cmds] |
|
Description: |
Displays active and stored configuration profiles |
|
Command |
Function |
|
&V0 |
Displays active and stored configuration profile 0 |
|
&V1 |
Displays active and stored configuration profile 1 |
|
DATA SET READY (DSR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Sn [cmds] |
|
Description: |
Selects DSR options |
|
Command |
Function |
|
í &S0 |
DSR forced high |
|
&S1 |
DSR high only while modem is handshaking or connected |
|
DATA TERMINAL READY (DTR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Dn [cmds] |
|
Description: |
Selects modem response to DTR |
|
Command |
Function |
|
í &D0 |
DTR override |
|
&D1 |
DTR toggle causes online command mode |
|
&D2 |
Normal DTR operations |
|
&D3 |
Resets on receipt of DTR |
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D<#> [cmds] |
|
Description: |
Dials telephone number according to any modifiers included in the string |
|
Note: |
Any combination of modifiers can be used to produce the desired dial functions in sequence. |
|
Command |
Function |
|
DP |
Pulse dialing enabled |
|
DR |
Answer mode enabled; originate mode disabled following handshake initiation. |
|
DS=n |
Dial stored telephone number n |
|
DT |
Tone dialing enabled/Pulse dialing disabled |
|
DW |
Dialing resumed following dial tone detection |
|
D, |
Dialing paused for amount of time specified in S8 register |
|
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
|
D@ |
Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
|
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
|
EXTENDED RESULT CODES | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Wn [cmds] |
|
Description: |
Enables selection of additional result codes. |
|
Command |
Function |
|
í W0 |
Modem reports DTE response codes |
|
W1 |
Modem reports DTE response codes |
|
W2 |
Modem reports DCE response codes |
|
W3 |
Modem reports DTE speed, modulation mode, error control, data compression, DCE speed |
|
W4 |
Modem reports DTE protocol, data compression, and DTE speed |
|
FLOW CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Kn [cmds] |
|
Description: |
Enables flow control options |
|
Command |
Function |
|
&K0 |
Flow control disabled |
|
&K3 |
RTS/CTS flow control enabled |
|
&K4 |
XON/XOFF flow control enabled |
|
PULSE DIALING RATIO | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Pn [cmds] |
|
Description: |
Selects pulse dial make/break ratio |
|
Command |
Function |
|
í &P0 |
39/61ms at 10pps (North America) |
|
&P1 |
33/67ms at 10pps (Europe) |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested |
|
Command |
Function |
|
I0 |
Reports four digit product code |
|
I1 |
Reports ROM checksum |
|
I2 |
Reports internal memory test |
|
I3 |
Reports device ID |
|
I4 |
Reports internal ID |
|
I5 |
Reports modem chip hardware configuration |
|
I6 |
Reports country code |
|
I7 |
Reports manufacturer firmware version |
|
I8 |
Reports modem firmware version |
|
I10 |
Reports modem board configuration |
|
SPEAKER VOLUME | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Ln [cmds] |
|
Description: |
Controls speaker volume |
|
Command |
Function |
|
L0 |
Low volume setting |
|
L1 |
Low volume setting |
|
í L2 |
Medium volume setting |
|
L3 |
Highest volume setting |
|
TEST MODES | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] &Tn |
|
Description: |
Selects test options |
|
Command |
Function |
|
&T0 |
End current test |
|
&T1 |
Begin local analog loopback test |
|
&T4 |
Grant remote digital loopback request |
|
&T5 |
Deny remote digital loopback request |
|
&T6 |
Request remote digital loopback |
|
&T7 |
Request remote digital loopback and self-test |
|
&T8 |
Begin local analog loopback and self-test |
|
TRELLIS CODING | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Un [cmds] |
|
Description: |
Enables/disables trellis coding |
|
Command |
Function |
|
í &U0 |
V.32 trellis coding enabled |
|
&U1 |
V.32 trellis coding disabled |
EXTENDED AT COMMAND SET
|
AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %En [cmds] |
|
Description: |
Controls auto-retrain mode and fallback/fall-forward |
|
Command |
Function |
|
%E0 |
Auto-retrain disabled |
|
%E1 |
Auto-retrain enabled |
|
CALLING TONE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] -Cn [cmds] |
|
Description: |
Controls whether the DTE will allow the modem to send a 1300Hz calling tone when originating |
|
Command |
Function |
|
-C0 |
Calling tone disabled |
|
-C1 |
1300hz calling tone enabled |
|
-C2 |
V.8 and 1300hz calling tone enabled |
|
COMPRESSION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Cn [cmds] |
|
Description: |
Selects data compression |
|
Command |
Function |
|
%C0 |
Data compression disabled |
|
%C1 |
MNP5 enabled |
|
CONNECT MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Nn [cmds] |
|
Description: |
Controls the type of connection the modem will operate in |
|
Command |
Function |
|
\N0 |
Normal mode enabled |
|
\N1 |
Normal mode enabled |
|
\N2 |
MNP mode enabled |
|
í \N3 |
Auto-reliable mode enabled |
|
\N4 |
V.42 reliable mode enabled |
|
FLOW CONTROL TYPE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Qn [cmds] |
|
Description: |
Sets type of flow control used by modem |
|
Command |
Function |
|
\Q0 |
Flow control disabled |
|
\Q1 |
Bi-directional XON/XOFF flow control enabled |
|
\Q2 |
CTS flow control by DCE enabled |
|
\Q3 |
Bi-directional RTS/CTS flow control enabled |
|
INACTIVITY TIMER | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Tn [cmds] |
|
Range: |
0-90 |
|
Unit: |
1 second |
|
Description: |
Sets the length of time that the modem does not receive information before it disconnects. |
|
V.42bis - MAXIMUM STRING LENGTH | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] "On [cmds] |
|
Range: |
6-250 |
|
Unit: |
Characters |
|
Description: |
Selects string size for V.42bis compression. Default is 32. |
VIOCE AT COMMAND SET
|
BUFFER THRESHOLD SELECTION | |
|
Format |
AT [cmds] +VBT=n [cmds] |
|
Description: |
Sets buffer threshold |
|
CALLER ID SELECTION | |
|
Format |
AT [cmds] +VCID=n [cmds] |
|
Description: |
Selects caller ID |
|
VOICE COMMAND MODE SILENCE DETECTION | |
|
Format |
AT [cmds] #VCSD=n [cmds] |
|
Description: |
Detects voice command mode silence |
|
DISTINCTIVE RING SELECTION | |
|
Format |
AT [cmds] +VDR=n [cmds] |
|
Description: |
Selects distinctive ring |
|
EVENT REPORTING AND MASKING | |
|
Format |
AT [cmds] +VEM=n [cmds] |
|
Description: |
Reports and masks events |
|
SPEAKERPHONE MICROPHONE GAIN | |
|
Format |
AT [cmds] +VGM=n [cmds] |
|
Description: |
Sets speakerphone microphone gain |
|
RECEIVE GAIN | |
|
Format |
AT [cmds] +VGR=n [cmds] |
|
Description: |
Selects receive gain |
|
SPEAKERPHONE SPEAKER GAIN | |
|
Format |
AT [cmds] +VGS=n [cmds] |
|
Description: |
Sets speakerphone speaker gain |
|
VOLUME SELECTION | |
|
Format |
AT [cmds] +VGT=n [cmds] |
|
Description: |
Selects volume |
|
INITIALIZE PARAMETER | |
|
Format |
AT [cmds] +VIP [cmds] |
|
Description: |
Sets voice initialization parameter |
|
INACTIVITY TIMER | |
|
Format |
AT [cmds] +VIT=n [cmds] |
|
Description: |
Sets DTE/DCE inactivity timer |
|
RELAY/SPEAKER | |
|
Format |
AT [cmds] +VLS=n [cmds] |
|
Description: |
Controls relay/speaker settings |
|
AUTOMATIC HANG-UP | |
|
Format |
AT [cmds] +VNH=n [cmds] |
|
Description: |
Controls automatic hang-up option |
|
RINGBACK DROPPED | |
|
Format |
AT [cmds] +VRA=n [cmds] |
|
Description: |
Determines amount of time before ringback is discontinued |
|
RINGBACK NOT RECIEVED | |
|
Format |
AT [cmds] +VRN=n [cmds] |
|
Description: |
Sets time for ringback to not appear |
|
RECORD MODE | |
|
Format |
AT [cmds] +VRX=n [cmds] |
|
Description: |
Determines record mode |
|
SILENCE DETECTION | |
|
Format |
AT [cmds] +VSD=n [cmds] |
|
Description: |
Detects quiet and silence |
|
COMPRESSION METHOD | |
|
Format |
AT [cmds] +VSM=n [cmds] |
|
Description: |
Selects compression method |
|
SPEAKERPHONE ENABLE | |
|
Format |
AT [cmds] +VSP=n [cmds] |
|
Description: |
Controls on/off of speakerphone |
|
SPEAKERPHONE TYPE | |
|
Format |
AT [cmds] #VSPS=n [cmds] |
|
Description: |
Selects speakerphone type |
|
BEEP TONE DURATION TIMER | |
|
Format |
AT [cmds] +VTD=n [cmds] |
|
Description: |
Sets the beep tone duration timer |
|
DTMF AND TONE GENERATION | |
|
Format |
AT [cmds] +VTS=n [cmds] |
|
Description: |
Controls DTMF and tone generation |
|
PLAY MODE | |
|
Format |
AT [cmds] +VTX=n [cmds] |
|
Description: |
Sets play mode |