Card Type	Frame relay adapter, Token Ring router
Processor	Motorola 68360
Processor Speed	Unidentified
Chip Set	Unidentified
Maximum Onboard Memory	8MB DRAM/2MB Flash RAM
I/O Options	Serial ports (3)
Network Transfer Rate	4Mbps/16Mbps
DSU Transfer Rate	56Kbps
ISDN Transfer Rate	64Kbps x 2
DSU Protocol	DDS
ISDN Protocol	Unidentified
Switch Type	Unidentified
Data Bus	External
Topology	Linear Bus/Star
Wiring Type	Unshielded twisted pair Shielded twisted pair
Boot ROM	Not available

CONNECTIONS
Function	Label	Function	Label
Reset button	BT1	CTP connector or ISDN connector (port 4)	CN4
Lamp test button	BT2	V.24 serial port (port 3)	CN5
Header for daughtercard	CN1	V.11, V.24, V.35, or V.36 serial port (port 2)	CN6
Unshielded twisted pair connector	CN2	120VAC power	CN7
Shielded twisted pair connector	CN3	Power switch	SW3
Note:When LED4 is on, press the lamp test button to reset it. Port 1 is the daughterboard.

USER CONFIGURABLE SETTINGS
Setting		Label	Position
»	Port 2 pin 22 used for ring indicator	SW1/1	Off
	Port 2 pin 22 used to enter test mode in DCE mode, ring indicator in DTE mode	SW1/1	On
»	Port 2 pin 25 used for test mode indicator	SW1/2	Off
	Port 2 pin 25 used for test mode indicator for DCE mode, busy out for DTE mode	SW1/2	On
»	Port 3 pin 22 used for ring indicator	SW1/3	Off
	Port 3 pin 22 used to enter test mode in DCE mode, ring indicator in DTE mode	SW1/3	On
»	Port 3 is normal serial port	SW1/4	Off
	Port 3 is the PAD port (forces serial configuration to 9600bps, no parity, 8 data bits, 1 stop bit)	SW1/4	On
»	Factory configured - do not alter	SW1/5	Off
»	Normal operation	SW1/6	Off
	Reset entire configuration to factory defaults	SW1/6	On
Note:To use SW1/6, power up the adapter, turn SW1/6 on, press the reset button, and turn SW1/6 back off again.

DRAM
Setting	On Board	S1
4MB	4MB	None
8MB	4MB	(1) 4MB x 9

PORT 2 TYPE
Setting	SW2/1	SW2/2	SW2/3	SW2/4	SW2/5	SW2/6
V.11 DTE	Off	Off	Off	Off	Off	On
V.11 DCE	Off	Off	Off	Off	Off	On
V.24 DTE	On	On	On	On	On	Off
V.24 DCE	On	On	On	On	On	Off
V.35 DTE	Off	Off	Off	Off	Off	On
V.35 DCE	Off	Off	Off	Off	Off	On
V.36 DTE	Off	Off	Off	Off	Off	On
V.36 DCE	Off	Off	Off	Off	Off	On
DSU	Off	Off	Off	Off	Off	On

PORT 2 TYPE (CON’T)
Setting	SW2/7	SW2/8	U1
V.11 DTE	On	On	V.11 module in position 1
V.11 DCE	On	On	V.11 module in position 2
V.24 DTE	Off	Off	V.24 module in position 1
V.24 DCE	Off	Off	V.24 module in position 2
V.35 DTE	On	On	V.35 module in position 1
V.35 DCE	On	On	V.35 module in position 2
V.36 DTE	On	On	V.36 module in position 1
V.36 DCE	On	On	V.36 module in position 2
DSU	On	On	DSU module in position 1

DIAGNOSTIC LED(S) (RESET AND POWER-UP)
LED1	LED3	Condition
Blinking	Off	Adapter is loading software into DRAM from flash RAM
Off	Blinking	Adapter is performing self-test
Off	Off	Adapter is initializing configuration
On	Off	Adapter is ready
Off	On	Self-test failed
Note:On reset or power-up, the LEDs should go through, in order, the first four actions shown above. If the adapter proceeds immediately to the fourth action, the code in the firmware is invalid.

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
LED1	Green	On	Software is running
LED1	Green	Off	Software not running
LED1	Green	Blinking	Software is downloading or card is booting
LED2	Green	On	Power is on
LED2	Green	Off	Power is off
LED3	Red	On	Test failed
LED3	Red	Off	No test in progress or test passed
LED3	Red	Blinking	Test in progress
LED4	Red	On	Processor did not reset timer in set time
LED4	Red	Off	Normal operation
LED5	Yellow	On	Card is transmitting MARK signal to port 1
LED5	Yellow	Off	Card is transmitting SPACE signal to port 1
LED6	Yellow	On	Card is receiving MARK signal from port 1
LED6	Yellow	Off	Card is receiving SPACE signal from port 1
LED7	Yellow	On	Card is transmitting MARK signal to port 2
LED7	Yellow	Off	Card is transmitting SPACE signal to port 2
LED8	Yellow	On	Card is receiving MARK signal from port 2
LED8	Yellow	Off	Card is receiving SPACE signal from port 2
LED9	Yellow	On	Card is transmitting MARK signal to port 3
LED9	Yellow	Off	Card is transmitting SPACE signal to port 3
LED10	Yellow	On	Card is receiving MARK signal from port 3
LED10	Yellow	Off	Card is receiving SPACE signal from port 3
LED11	Yellow	On	Card is transmitting MARK signal to port 4
LED11	Yellow	Off	Card is transmitting SPACE signal to port 4
LED12	Yellow	On	Card is receiving MARK signal from port 4
LED12	Yellow	Off	Card is receiving SPACE signal from port 4
LED13	Yellow	On	Card is transmitting MARK signal to network
LED13	Yellow	Off	Card is transmitting SPACE signal to network
LED14	Yellow	On	Card is receiving MARK signal from network
LED14	Yellow	Off	Card is receiving SPACE signal from network

Card Type	Serial
I/O Options	Serial port

CONNECTIONS
Function	Label	Function	Label
V.11 V.24, V.35, V.36, or DSU port	CN1	Header to main board (on both front and back of card)	CN2B

USER CONFIGURABLE SETTINGS
Setting		Label	Position
»	Pin 22 used for ring indicator	P22	Pins 2 & 3 closed
	Pin 22 used to enter test mode in DCE mode, ring indicator in DTE mode	P22	Pins 1 & 2 closed
»	Pin 25 used for test mode indicator	P25	Pins 1 & 2 closed
	Pin 25 used for test mode indicator for DCE mode, busy out for DTE mode	P25	Pins 2 & 3 closed

SERIAL PORT TYPE
Setting	SW1/1	SW1/2	SW1/3	SW1/4	SW1/5	SW1/6
V.11 DTE	Off	Off	Off	Off	Off	On
V.11 DCE	Off	Off	Off	Off	Off	On
V.24 DTE	On	On	On	On	On	Off
V.24 DCE	On	On	On	On	On	Off
V.35 DTE	Off	Off	Off	Off	Off	On
V.35 DCE	Off	Off	Off	Off	Off	On
V.36 DTE	Off	Off	Off	Off	Off	On
V.36 DCE	Off	Off	Off	Off	Off	On
DSU	Off	Off	Off	Off	Off	On

SERIAL PORT TYPE (CON’T)
Setting	SW1/7	SW1/8	U1
V.11 DTE	On	On	V.11 module in position 1
V.11 DCE	On	On	V.11 module in position 2
V.24 DTE	Off	Off	V.24 module in position 1
V.24 DCE	Off	Off	V.24 module in position 2
V.35 DTE	On	On	V.35 module in position 1
V.35 DCE	On	On	V.35 module in position 2
V.36 DTE	On	On	V.36 module in position 1
V.36 DCE	On	On	V.36 module in position 2
DSU	On	On	DSU module in position 1

Card Type	ISDN TA
ISDN Transfer Rate	64Kbps x 2
ISDN Protocol	Unidentified
Switch Type	Unidentified

CONNECTIONS
Function	Label	Function	Label
Line in/out	CN1	Line in/out	CN3
Header to main board (on both front and back of card)	CN2B
Note:Two connectors are provided so the user can daisy-chain devices on the S/T bus.

USER CONFIGURABLE SETTINGS
Setting		Label	Position
»	S/T bus not terminated	SW1	Off
	S/T bus terminated	SW1	On

Card Type	ISDN TA
ISDN Transfer Rate	64Kbps x 2
ISDN Protocol	Unidentified
Switch Type	Unidentified

CONNECTIONS
Function	Label	Function	Label
Line out	CN1	Header to main board (on both front and back of card)	CN2B

Card Type	DDS DSU
DSU Transfer Rate	56Kbps
Modulation Protocol	Unidentified

CONNECTIONS
Function	Label	Function	Label
Line out	CN1	Header to main board (on both front and back of card)	CN2B