QS-200M/300M

QUATECH, INC.

QS-200M/300M

Card Type

Serial controller

Chipset/Controller

16450/16550 UART

I/O Options

Serial ports (4)

Maximum DRAM

N/A

CONNECTIONS

Purpose

Location

Purpose

Location

Serial port 1 - RJ-11

CN1

Serial port 3 - RJ-11

CN3

Serial port 2 - RJ-11

CN2

Serial port 4 - RJ-11

CN4

INPUT CLOCK CONFIGURATION

MHz

J1

»
1.8432MHz

Pins 1 & 4, 2 & 3, 5 & 6 closed

3.6864MHz

Pins 2 & 3, 4 & 5 closed

9.216MHz

Pins 1 & 2, 5 & 6 closed

18.432MHz

Pins 2 & 5 closed

DUPLEX SELECTION

Setting

J2/A

J2/B

J2/C

J2/D

»
Port 1 full duplex mode

Open

N/A

N/A

N/A

Port 1 half duplex mode

Closed

N/A

N/A

N/A

»
Port 2 full duplex mode

N/A

Open

N/A

N/A

Port 2 half duplex mode

N/A

Closed

N/A

N/A

»
Port 3 full duplex mode

N/A

N/A

Open

N/A

Port 3 half duplex mode

N/A

N/A

Closed

N/A

»
Port 4 full duplex mode

N/A

N/A

N/A

Open

Port 4 half duplex mode

N/A

N/A

N/A

Closed

INTERRUPT SELECT

IRQ

J3/A

J3/B

J3/C

J3/D

J3/E

J3/F

IRQ2

Closed

Open

Open

Open

Open

Open

IRQ3

Open

Closed

Open

Open

Open

Open

IRQ4

Open

Open

Closed

Open

Open

Open

IRQ5

Open

Open

Open

Closed

Open

Open

IRQ6

Open

Open

Open

Open

Closed

Open

IRQ7

Open

Open

Open

Open

Open

Closed

Note: All ports share the same IRQ.

I/O ADDRESS CONFIGURATION

Base Address

SW1

SW2

»
300h

1, 2, 3, 4, 5 & 6 On

3, 4 & 5 On

6A0h

1, 2, 3, 4 & 5 On

2 & 4 On

5220h

1, 3, 5 & 6 On

2, 3 & 4 On

Note (1): The address range for the QS-200M/300M is from 0 to FFFFh. The switches are a binary representation of the addresses. When a switch is off, the corresponding bit is set to 1 and has the following decimal value: SW1/1=8, SW1/2=4, SW1/3=2, SW1/4=1, SW1/5=8, SW1/6=4, SW2/1=2, SW2/2=1, SW2/3=8, SW2/4=4, SW2/5=2. The QS-200M/300M requires 32 consecutive address locations for all four serial ports.

Note (2): The base address selected above is for Port 1. To obtain the addresses for the other ports, add to the Port 1 address the following numbers:

Port 2 address = Port 1 address + 8

Port 3 address = Port 1 address + 16

Port 4 address = Port 1 address + 24

INTERRUPT STATUS REGISTER

Setting

SW2/6

Interrupt status register enabled

On

Interrupt status register disabled

Off

Card Type	Serial controller
Chipset/Controller	16450/16550 UART
I/O Options	Serial ports (4)
Maximum DRAM	N/A

CONNECTIONS
Purpose	Location	Purpose	Location
Serial port 1 - RJ-11	CN1	Serial port 3 - RJ-11	CN3
Serial port 2 - RJ-11	CN2	Serial port 4 - RJ-11	CN4

INPUT CLOCK CONFIGURATION
MHz		J1
»	1.8432MHz	Pins 1 & 4, 2 & 3, 5 & 6 closed
	3.6864MHz	Pins 2 & 3, 4 & 5 closed
	9.216MHz	Pins 1 & 2, 5 & 6 closed
	18.432MHz	Pins 2 & 5 closed

DUPLEX SELECTION
Setting		J2/A	J2/B	J2/C	J2/D
»	Port 1 full duplex mode	Open	N/A	N/A	N/A
	Port 1 half duplex mode	Closed	N/A	N/A	N/A
»	Port 2 full duplex mode	N/A	Open	N/A	N/A
	Port 2 half duplex mode	N/A	Closed	N/A	N/A
»	Port 3 full duplex mode	N/A	N/A	Open	N/A
	Port 3 half duplex mode	N/A	N/A	Closed	N/A
»	Port 4 full duplex mode	N/A	N/A	N/A	Open
	Port 4 half duplex mode	N/A	N/A	N/A	Closed

INTERRUPT SELECT
IRQ	J3/A	J3/B	J3/C	J3/D	J3/E	J3/F
IRQ2	Closed	Open	Open	Open	Open	Open
IRQ3	Open	Closed	Open	Open	Open	Open
IRQ4	Open	Open	Closed	Open	Open	Open
IRQ5	Open	Open	Open	Closed	Open	Open
IRQ6	Open	Open	Open	Open	Closed	Open
IRQ7	Open	Open	Open	Open	Open	Closed
Note: All ports share the same IRQ.

I/O ADDRESS CONFIGURATION
Base Address		SW1	SW2
»	300h	1, 2, 3, 4, 5 & 6 On	3, 4 & 5 On
	6A0h	1, 2, 3, 4 & 5 On	2 & 4 On
	5220h	1, 3, 5 & 6 On	2, 3 & 4 On
	Note (1): The address range for the QS-200M/300M is from 0 to FFFFh. The switches are a binary representation of the addresses. When a switch is off, the corresponding bit is set to 1 and has the following decimal value: SW1/1=8, SW1/2=4, SW1/3=2, SW1/4=1, SW1/5=8, SW1/6=4, SW2/1=2, SW2/2=1, SW2/3=8, SW2/4=4, SW2/5=2. The QS-200M/300M requires 32 consecutive address locations for all four serial ports. Note (2): The base address selected above is for Port 1. To obtain the addresses for the other ports, add to the Port 1 address the following numbers: Port 2 address = Port 1 address + 8 Port 3 address = Port 1 address + 16 Port 4 address = Port 1 address + 24

INTERRUPT STATUS REGISTER
Setting	SW2/6
Interrupt status register enabled	On
Interrupt status register disabled	Off