TIARA COMPUTER SYSTEMS, INC.

ARCNET LanCard AT TP

NIC Type

ARCnet

Transfer Rate

2.5Mbps

Data Bus

16-bit ISA

Topology

Star

Wiring Type

Shielded twisted pair

Unshielded twisted pair

Boot ROM

Available

NODE ADDRESS - SW4

Node

SW4/1

SW4/2

SW4/3

SW4/4

SW4/5

SW4/6

SW4/7

SW4/8

0

-

-

-

-

-

-

-

-

1

Off

Off

Off

Off

Off

Off

Off

On

2

Off

Off

Off

Off

Off

Off

On

Off

3

Off

Off

Off

Off

Off

Off

On

On

4

Off

Off

Off

Off

Off

On

Off

Off

251

On

On

On

On

On

Off

On

On

252

On

On

On

On

On

On

Off

Off

253

On

On

On

On

On

On

Off

On

254

On

On

On

On

On

On

On

Off

255

On

On

On

On

On

On

On

On

Note:Node address 0 is used for messaging between nodes and must not be used.

A total of 255 node address settings are available. The switches are a binary representation of the decimal node addresses. Switch 8 is the Least Significant Bit and switch 1 is the Most Significant Bit. The switches have the following decimal values: switch 1=1, 2=2, 3=4, 4=8, 5=16, 6=32, 7=64, 8=128. Turn on the switches and add the values of the on switches to obtain the correct node address. (On=1, off=0)

INTERRUPT REQUEST

IRQ

JP1

JP2

JP3

JP4

JP5

JP6

JP7

JP8

JP9

JP10

JP11

»

2

Open

Open

Open

Open

Open

Closed

Open

Open

Open

Open

Open

 

3

Open

Open

Open

Open

Open

Open

Open

Open

Open

Open

Closed

 

4

Open

Open

Open

Open

Open

Open

Open

Open

Open

Closed

Open

 

5

Open

Open

Open

Open

Open

Open

Open

Open

Closed

Open

Open

 

6

Open

Open

Open

Open

Open

Open

Open

Closed

Open

Open

Open

 

7

Open

Open

Open

Open

Open

Open

Closed

Open

Open

Open

Open

 

10

Open

Open

Open

Open

Closed

Open

Open

Open

Open

Open

Open

 

11

Open

Open

Open

Closed

Open

Open

Open

Open

Open

Open

Open

 

12

Open

Open

Closed

Open

Open

Open

Open

Open

Open

Open

Open

 

14

Open

Closed

Open

Open

Open

Open

Open

Open

Open

Open

Open

 

15

Closed

Open

Open

Open

Open

Open

Open

Open

Open

Open

Open

DIAGNOSTIC CONFIGURATION

Setting

JP12

»

Enhanced diagnostics disabled

Pins 1 & 2 Closed

 

Enhanced diagnostics enabled

Pins 2 & 3 Closed

Note:The enhanced diagnostics are compatable only with the dirver that was shipped with this card. When the diagnostics are enabled, features such as an ARCnet duplicate Node ID search, are activated.

INTERNAL NETWORK TERMINATION

Setting

JP13

»

Internal network termination disabled

Pins 2 & 3 Closed

 

Internal network termination enabled

Pins 1 & 2 Closed

Note:A terminator plug need not be used if this option is enabled and the card is located at the start or end point of the network cable.

BOOT ROM

Setting

SW1/1

»

Disabled

Off

 

Enabled

On

RIM BUFFER ADDRESS CONFIGURATION

Buffer Address

SW1/2

SW1/3

SW1/4

SW1/5

SW1/6

SW1/7

SW1/8

xC0OOh

Off

On

On

Off

Off

Off

Off

xC4OOh

Off

On

On

Off

Off

Off

On

xCCOOh

Off

On

On

Off

Off

On

On

xD0OOh

Off

On

On

Off

On

Off

Off

xD4OOh

Off

On

On

Off

On

Off

On

xD8OOh

Off

On

On

Off

On

On

Off

xDCOOh

Off

On

On

Off

On

On

On

xE000h

Off

On

On

On

Off

Off

Off

Notes: Place one digit from the following table in front of the address given above to get the complete Address.

SW3/switch 4 should be set to On for 128KB, or Off for 16KB.

RIM BUFFER EXTENDED ADDRESS CONFIGURATION

Segment

SW3/1

SW3/2

SW3/3

SW3/5

SW3/6

SW3/7

SW3/8

»

0xxxx

On

Off

Off

Off

Off

Off

Off

 

1xxxx

On

Off

Off

Off

Off

Off

On

 

2xxxx

On

Off

Off

Off

Off

On

Off

 

3xxxx

On

Off

Off

Off

Off

On

On

 

4xxxx

On

Off

Off

Off

On

Off

Off

 

5xxxx

On

Off

Off

Off

On

Off

On

 

6xxxx

On

Off

Off

Off

On

On

Off

 

7xxxx

On

Off

Off

Off

On

On

On

 

8xxxx

On

Off

Off

On

Off

Off

Off

 

9xxxx

On

Off

Off

On

Off

Off

On

 

Axxxx

On

Off

Off

On

Off

On

Off

 

Bxxxx

On

Off

Off

On

Off

On

On

 

Cxxxx

On

Off

Off

On

On

Off

Off

 

Dxxxx

On

Off

Off

On

On

Off

On

 

Exxxx

On

Off

Off

On

On

On

Off

 

Fxxxx

On

Off

Off

On

On

On

On

Note:Place the digit found in this table in front of the address given in the previous table to get the complete RIM buffer address. A setting other than zero in this table will place the buffer into extended memory at the aforementioned address. For example, a setting of 2 will place the buffer into the 2nd megabyte of extended memory, a setting of C will place the buffer into the 12th megabyte of extended memory. Starting from the base address. make sure that the next 16 to 128KB of memory (see above notes) are not used.

Important: The software drivers supplied with this card do not support extended memory.

EXTENDED TIMEOUT CONFIGURATION

Distance

Response Time

Reconfiguration

SW2/1

SW2/2

»

4.8 miles

74.7µs

840ms

On

On

 

21.0 miles

283.4µs

1680ms

On

Off

 

42.5 miles

561.8µs

1680ms

Off

On

 

85.6 miles

1118.6µs

1680ms

Off

Off

Note:The distance given is the maximum distance between the two furthest nodes on the network.

I/O BASE ADDRESS

Address

SW2/3

SW2/4

SW2/5

SW2/6

SW2/7

SW2/8

»

2E0h

On

Off

On

On

On

Off

 

260h

On

Off

Off

On

On

Off

 

290h

On

Off

On

Off

Off

On

 

2B0h

On

Off

On

Off

On

On

 

300h

On

On

Off

Off

Off

Off

 

350h

On

On

Off

On

Off

On

 

380h

On

On

On

Off

Off

Off

 

3E0h

On

On

On

On

On

Off