M 1 6 0 3 S A U > 1 1 / 1 9 9 5 FUJITSU NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 3456| | | Capacity form/unform 544/ MB Heads 3| | | Seek time / track 10.0/ 3.0 ms Sector/track | | | Controller SCSI2 SI/FAST Precompensation Cache/Buffer 512 KB FIFO RING Landing Zone Data transfer rate 6.000 MB/S int Bytes/Sector 512 10.000 MB/S ext SYNC Recording method operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 60 Power: sleep W Humidity % 8 80 | 5 95 standby W Altitude km -0.300 3.000| -0.300 12.000 idle W Shock g 5 | 505 seek W Rotation RPM 5400 read/write W Acoustic dBA 38 spin-up W ECC Bit MTBF h 800000 Warranty Month 24 Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** FUJITSU M1603S/1606S AFTER NOVEMBER 1995 JUMPER SETTING +---------------------------------------------------------+ | |XXI | CNH1----+ |XXN | +----+ |XXT | +--+ |XXE | +--CN6 |XXR | |XXF | |XXA | +--+ |XXC | +--CNH3 |XXE | |XX | |XX | |XX | |XX | +-1 | | +-+CN5 |XX Power | After 11/1995 |XX +---------------------------------------------------------+ ********************************************************************** J U M P E R S ********************************************************************** FUJITSU M1603S/1606S AFTER 11/95 JUMPER SETTING Jumper Setting ============== x = Factory default setting CNH1 SCSI ID ------------- +----------+-----------------------+ | SCSI ID | Jumpers | | | 5-6 | 3-4 | 1-2 | +----------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | +----------+-------+-------+-------+ | 1 | OPEN | OPEN | CLOSED| +----------+-------+-------+-------+ | 2 | OPEN | CLOSED| OPEN | +----------+-------+-------+-------+ | 3 | OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+ | 4 | CLOSED| OPEN | OPEN | +----------+-------+-------+-------+ | 5 | CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+ | 6 | CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+ |x 7 | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+ NOTE Always ensure that the device ID selected is unique to the SCSI bus. CNH1 Spindle Motor Control -------------------------- Pins 7-8 OPEN Spindle motor controlled by START/STOP command xCLOSED Spindle motor on at power up CNH1 Synchronous Data Transfer Mode ----------------------------------- Pins 9-10 CLOSED Synchronous Data Transfer Mode disabled (default) OPEN Synchronous Data Transfer Mode enabled CNH1 Reselection retry ---------------------- Pins 11-12 CLOSED Reselection retry = unlimited (default) OPEN Reselection retry = 10 times CNH1 NOT USED ------------- Pins 13-14 NOT USED! CNH1 Active termination ----------------------- Pins 15-16 CLOSED Active termination enabled (default) OPEN Active termination disabled CN6 Remote SCSI ID Connector ---------------------------- +1-3-5-7-9+ |o o o o o| Side View |o o o o o| +2-4-6-8-10 +------------+----------+ | PINS | SIGNAL | +------------+----------+ |Pin 2 |-ID0 | +------------+----------+ |Pin 4 |-ID1 | +------------+----------+ |Pin 6 |-ID2 | +------------+----------+ |Pins 1,3,5,9|GND | +------------+----------+ |Pins 7-8 |RESERVED | +------------+----------+ |Pin 10 |Spindle | | |Sync pulse| +------------+----------+ CNH3 Terminal SCSI Termination Power ------------------------------------ 1-2 CLOSED Power is supplied to the terminating resistor from the 3-4 CLOSED IDD and TERMPWR pin. Power is also supplied to the (default) TERMPWR pin from the IDD. (Pin 26 of the interface) 1-2 CLOSED The Termpwr pin is not used. Power is supplied to the 3-4 OPEN IDD terminating resistor only from the IDD. 1-2 OPEN Power is not supplied to the terminating resistor from 3-4 CLOSED the IDD, only from the TERMPWR pin. CN5 External operator panel connector ------------------------------------- Pin 01 LED(V) Pin 02 -LED