S H D - 3 2 1 1 A A P O L L O 2 1 0 SAMSUNG NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 2570| 1002| | Capacity form/unform 213/ MB Heads 2| 8| | Seek time / track 13.0/ 4.0 ms Sector/track | 52| | Controller IDE / AT Precompensation Cache/Buffer 64 KB Landing Zone Data transfer rate 3.869 MB/S int Bytes/Sector 512 8.000 MB/S ext Recording method RLL 1/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 65 Power: sleep 1.8 W Humidity % 8 80 | 8 95 standby 1.9 W Altitude km -0.061 3.048| 12.192 idle 3.6 W Shock g 10 | 75 seek 5.8 W Rotation RPM 3600 read/write 4.0 W Acoustic dBA 40 spin-up W ECC Bit 88,REED SOLOMON MTBF h 250000 Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** SAMSUNG SHD-3211A/3212A/3171A1/3172A1 USER'S MANUAL 264 034001 BAAK +---------------------------------------------------------+ | +-+C/D |XX A1 | +-+ | |DSP |XX | | | +-+ |XX | | | |XX |++++ |XX I |+-+External |XX N | LED |XX T | |*X E | |XX R | |XX F | |XX A | |XX C | |XX E | |X1 | | | |XX | |XX Power +---------------------------------------------------------+ 1 ********************************************************************** J U M P E R S ********************************************************************** SAMSUNG SHD-3211A/3212A/3171A1/3172A1 USER'S MANUAL 264 034001 BAAK Jumper Setting ============== 8-pin User Configurations Jumper Block -------------------------------------- +---+ +---+ +---+ |o o|C/D |xxx|C/D |xxx|C/D |o o|DSP |o o|DSP |xxx|DSP |o o| |o o| |o o| |o o| |o o| |o o| +---+ +---+ +---+ 2 Drive 1 Drive 2 Drive SLAVE MASTER ********************************************************************** I N S T A L L ********************************************************************** SAMSUNG SHD-3211A/3212A/3171A1/3172A1 USER'S MANUAL 264 034001 BAAK Notes on Installation ===================== Shipping -------- When transporting or shipping a drive, a SAMSUNG-approved container must be used. Keep your original box. Shipping a drive in a non- approved container will void the drive warranty. Samsung recommends shipping by an air-ride carrier experienced in handling computer equipment. Environment ----------- - Avoid harsh humidity and temperature. Do not place near the magnet. Samsung Hard Disk Drives do not require Low level Format because Samsung Drives have been formatted before shipping in the factory. - The head/disk assembly is sealed and does not contain any user- serviceable components. Tampering with the warranty label will void the warranty. Warranty -------- The terms of your warranty are determined by your authorized Samsung Distributor or Dealer. Warranties do not extend to the data stored on Drives. Installing your Disk Drive -------------------------- 1. Turn off the system power. 2. Remove the top cover of your computer according to the instructions in your system manual. 3. Master/Slave configuration. 4. Most interface cables have a red stripe on one side to designate Pin 1. Make sure Pin 1 at the cable connector is aligned to Pin 1 at the drive connector and Pin 1 at the motherboard or interface host adapter connector. The maximum cable length is 18 inches (0.46m, ATA Rev. 3.0). 5. Connect the power cable to the drive 4-pin power connector. 6. Position drive in the mounting slot of your system. #6-32 UNC screws should be used. Be careful not to over-tighten screws. You could damage the PCBA. ********************************************************************** F E A T U R E S ********************************************************************** SAMSUNG SHD-3211A/3212A/3171A1/3172A1 USER'S MANUAL 264 034001 BAAK System startup and operation ---------------------------- 1. Power up the system. 2. Run the SETUP program. 3. Formatting the drive. Samsung AT interface drives are low-level formatted at the factory an do not need low-level formatting. Partition the drive using the DOS FDISK utility. Then, high level format the drive using the DOS FORMAT utility. Use DOS 3.3 or higher. CAUTION If you partition or format a drive at any level you erase all your data. Backup the drive first. Samsung assumes no liability for lost user data.