S H D - 3 0 2 8 0 A A P O L L O 2 8 0 SAMSUNG NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 2668| 869| | Capacity form/unform 280/ MB Heads 2| 10| | Seek time / track 12.0/ ms Sector/track | 63| | Controller IDE / ATA2 FAST/ENHA Precompensation Cache/Buffer 128 KB Landing Zone Data transfer rate 5.000 MB/S int Bytes/Sector 512 11.000 MB/S ext PIO3 Recording method operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | Power: sleep W Humidity % | standby W Altitude km | idle W Shock g | 75 seek W Rotation RPM 3600 read/write W Acoustic dBA spin-up W ECC Bit 88,REED SOLOMON MTBF h 250000 Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** SAMSUNG SHD-30280A/30420A/30560A USER`S MANUAL 1994 +---------------------------------------------------------+ | +-+DCF |XX | +-+ | |DSP |XX | | | +-+-C/D |XX | | | |XX ++ +-+ |XX I ++ External |XX N | LED |XX T | |*X E | |XX R | |XX F | |XX A | |XX C | |XX E | |X1 | | | |XX | |XX Power +---------------------------------------------------------+ 1 ********************************************************************** J U M P E R S ********************************************************************** SAMSUNG SHD-30280A/30420A/30560A USER`S MANUAL 1994 Jumper Setting ============== 8-pin User Configurations Jumper Block -------------------------------------- +---+ +---+ +---+ |o o| |o o| |o o| |o o|DCF |o o|DCF |o o|DCF |o o|DSP |o o|DSP |xxx|DSP |o o|-C/D |xxx|-C/D |xxx|-C/D +---+ +---+ +---+ 2 Drive 1 Drive 2 Drive SLAVE MASTER DCF Jumper ---------- The following table shows the recommended drive configuration for the SHD-30280A/30420A/30560A drives. +-------+-----+-----+----+-----------+----------+--------------+ |Model | Cyl.|Heads|Sec.|Formatted |Formatted |DCF Jumper | | | | | |CMOS MBytes|DOS MBytes| | +-------+-----+-----+----+-----------+----------+--------------+ |30280A | 869 | 10 | 63 | 267.3 | 280.3 |NONE | +-------+-----+-----+----+-----------+----------+--------------+ |30420A | 856 | 16 | 63 | 401.3 | 420.7 |NONE | +-------+-----+-----+----+-----------+----------+--------------+ |30560A |1024 | 16 | 63 | 503.5 | 528.4 |INSTALLED | | |1086 | 16 | 63 | 547.8 | 560.9 |NONE (default)| +-------+-----+-----+----+-----------+----------+--------------+ ********************************************************************** I N S T A L L ********************************************************************** SAMSUNG SHD-30280A/30420A/30560A USER`S MANUAL 1994 Notes on Installation ===================== Shipping -------- When transporting or shipping a drive, a SAMSUNG-approved container must be used. Keep your original box. Shipping a drive in a non- approved container will void the drive warranty. Samsung recommends shipping by an air-ride carrier experienced in handling computer equipment. Environment ----------- - Avoid excessive humidity and temperature. - Do not place near a magnet. - Samsung Hard Disk Drives do not require Low level Format because Samsung Drives have been formatted before shipping in the factory. - The head/disk assembly is sealed and does not contain any user- serviceable components. Tampering with the warranty label will void the warranty. Warranty -------- The terms of your warranty are determined by your authorized Samsung Distributor or Dealer. Warranties do not extend to the data stored on Drives. Installing your Hard Disk Drive ------------------------------- 1. Turn off the system power. 2. Remove the cover of your computer according to the instructions in your system manual. 3. Master/Slave configuration. 4. Most interface cables have a red stripe on one side to designate Pin 1. Make sure Pin 1 at the cable connector is aligned to Pin 1 at the drive connector and Pin 1 at the motherboard or interface host adapter connector. The maximum cable length is 18 inches (0.46m, ATA Rev. 3.0). 5. Connect the power cable to the drive 4-pin power connector. Make sure the connector is fully seated. 6. When the interface cable, power cable are firmly seated, secure the drive in the mounting slot. Use the six #32 UNC screws that came yith your SAMSUNG drive. To prevent DAMAGE to the printed circuit board assembly, do not over tighten the UNC screws. DC Power and pin connector assignments -------------------------------------- +------------+ pin 1 +12 VDC | 1 2 3 4 | pin 2 +12 Volts Return \------------/ pin 3 + 5 Volts Return pin 4 + 5 VDC ********************************************************************** F E A T U R E S ********************************************************************** SAMSUNG SHD-30280A/30420A/30560A USER'S MANUAL 1994 System startup and operation ---------------------------- 1. Turn on the system power. 2. Run the SETUP program. Use a system utility, such as SETUP, to enter the drive configuration into the system CMOS. If the CMOS setup utility does not offer our drive's configuration and does not support "user defined" drive type, select a drive type with a capacity less than or equal to the capacity given in the specification. BIOS in present systems may be limited to maximum of 1024 cylinders. So SHD-30560A has two configurations. The BIOS in most systems limits disk drives to 1024 cylinders. If you are going to install the SHD-30560A with the default configuration, your system should be able to support more than 528MB IDE drive. A BIOS or a device driver is required to overcome the limit of conventional BIOS. Refer to your system manual. If your system cannot recognize this disk size, install the DCF jumper and perform a high- level format again. Your system should than recognize the disk size as approximately 528MB. 3. Formatting the drive. SAMSUNG low-level formats all AT interface drives at the factory. It is not necessary to do a low-level format again. CAUTION If you partition or format a drive at any level, you lose all of data. BACKUP the drive first. SAMSUNG assumes no liability for lost user data.