8 4 3 2 0 A 8 C R Y S T A L 1 0 8 0 MAXTOR Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders | 8400| | Capacity form/unform 4320/ MB Heads 8| 16| | Seek time / track 11.0/ 2.0 ms Sector/track | 63| | Controller IDE / ATA2 FAST/ENHA Precompensation Cache/Buffer 256 KB Landing Zone Data transfer rate 8.000 MB/S int Bytes/Sector 512 16.700 MB/S ext PIO4 Recording method operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 71 Power: sleep 1.0 W Humidity % 5 95 | 5 95 standby 1.3 W Altitude km -0.061 3.048| -0.061 12.192 idle 4.0 W Shock g 35 | 200 seek 8.3 W Rotation RPM 4480 read/write 4.8 W Acoustic dBA 36 spin-up 13.7 W ECC Bit MTBF h Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** MAXTOR 84320/83201/82580/82100/81620/81081A JUMPER SETTING Pin 1 J1 IDE Connector | J2 Power +----------- --------+-++-----------+---------+ | .................... || @ * * o | | | .......... ......... || @ o o o o | O O O O | +----------------------++-----------+---------+ | | | | | | | | | | | | | | | | | | J50 Master/Slave ---+ | | | | | | | +- +12V (Yellow) J48 Cable Select -----+ | | | | | +--- +12V Return (Black) J46 4092 Cyl Limitation + | | | +----- +5V Return (Black) J44 Factory Reserved -----+ | +------- +5V (Red) J42 Factory Reserved -------+ @ = Default Jumped Positions * = "Spare" Jumper Position o = Default Open Positions ********************************************************************** J U M P E R S ********************************************************************** MAXTOR 84320/83201/82580/82100/81620/81081 JUMPER SETTING Jumper Setting ============== Jumper Designations |J50|J48|J46|J44|J42| +-------------------------------------+---+---+---+---+---+ | Master/Slave | | | | | | | Only Drive in single drive system* | J | | | | | | Master in a dual drive system* | J | | | | | | Slave in a dual drive system | O | | | | | +-------------------------------------+---+---+---+---+---+ | Cable Select | | | | | | | Disabled* | | O | | | | | Enabled | | J | | | | +-------------------------------------+---+---+---+---+---+ | 4092 Cylinder Option | | | | | | | Disabled* | | | O | | | | Enabled | | | J | | | +-------------------------------------+---+---+---+---+---+ | Factory Reserved | | | | O | | +-------------------------------------+---+---+---+---+---+ | Factory Reserved | | | | | | +-------------------------------------+---+---+---+---+---+ J=Jumpered O=Open *=Default Systems Using Cable Select -------------------------- Most systems do not use this feature. Unless you are sure that the system that the Maxtor hard drive is being installed in uses Cables Select, do not set up the drive with this feature enabled. Maxtor hard drives support Cable Select - which allows the system to identify Devuce 0 and Device 1 drives on the interface cable. If your system manufacturer for specific procedures for installing hard drives. On Maxtor CrystalMax hard drives, the Cable Select is enabled by installing a jumper on J48. When J48 is installed, remove the jumper from J50. WARNING Do NOT install Cable Select jumper unless you are sure that the system requires this feature. The drive will not operate correctly in systems which do not support Cable Select. System Hangs During Boot ------------------------ If the system hangs after installing the Maxtor hard drive, either before or after setting the system BIOS, the system may have a BIOS with a cylinder limitation. This may occur for hard drives with capacities larger than 2.1GB. If this happens, do the following: 1. Turn the system OFF. 2. Install the cylinder reduction jumper (J46) on the drive using the spare jumper across pins J46 and J48; or, if the drive is installed as a Slave, store the spare jumper across J42 and J44. 3. If the BIOS was set to AUTO DETECT, boot the system with the MAX BLAST installation software diskette to complete the hard drive installation. If other BIOS setting were used, access the BIOS SETUP program and set the BIOS parameters to a Type 9 for the Maxtor hard drive. Then boot the system with the MAXBLAST installation software diskette to complete the hard drive installation. NOTE When this jumper is installed, the Maxtor hard drive must be prepared using the MAXBLAST installation software.