W D A - 3 1 6 0 IBM Native| Translation ------+-----+-----+----- Form 3.5"/HH Cylinders | | | Capacity form/unform 160/ MB Heads | | | Seek time / track / ms Sector/track | | | Controller IDE / AT Precompensation Cache/Buffer KB Landing Zone Data transfer rate MB/S int Bytes/Sector 512 MB/S ext Recording method operating | non-operating -------------+-------------- Supply voltage Temperature *C | Power: sleep W Humidity % | standby W Altitude km | idle W Shock g | seek W Rotation RPM read/write W Acoustic dBA spin-up W ECC Bit MTBF h Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** J U M P E R S ********************************************************************** IBM WDA-380/3160 JUMPER SETTING Jumper Setting ============== LED port -------- Pin Status Description 1 OUT -LED 2 OUT +LED +LED This pin has a maximum current source capability about +18 mA at nominal condition. -LED This pin has a current sink capability about +100 mA at 0.25 V in the worst case. Switch setting -------------- 4-bit dip switch on the control card is available for drive configuration. Bit No. Name Description 1 IORDY If a host supports IORDY signal, this bit must be set ON. 2 -DRV0/DRV1 When set ON, the drive is set as drive 0 (master) When set OFF, the drive is set as drive 1 (slave) 3 -CAM/AT This bit must be set ON 4 ------ NOT AVAILABLE ********************************************************************** G E N E R A L ********************************************************************** IBM AT INSTALLATION (IDE-AT1) IDE Installation Guide Generic Installation requirements ------------------------- To install an IDE drive inside your computer, you must have: 1 The documentation that came with your computer. 2 The documentation that came with your hard drive. 3 A small, flat blade screwdriver. WARNING: Do not open the static-protective bag containing the drive until instructed to do so. Static electricity can damage the drive. Preparing the drive for installation ------------------------------------ Master drive If this drive is the first or primary hard disk drive to be installed inside your computer, check the manual that came with your hard drive to locate the Master setting. If your drive is set to a Master, do not change the jumper position. Slave drive If this drive is the second or secondary hard disk drive in your computer, you must change the jumper position on the drive to Slave. Refer to the manual that came with your hard disk drive to locate the Slave setting. To change the jumper on the hard disk drive: 1 Remove the drive from the static-protective bag and place it on top of the bag. 2 Refer to your manual and locate the pins. 3 If you need to change the setting, grasp the jumper and pull it off the pins. 4 Line up the two holes in the bottom of the jumper with the approprate two pins on the drive. Push the jumper onto the pins until the jumper is completely seated and covers both pins. Installing the drive -------------------- For the specific information on installing a hard disk drive, refer to the documentation that came with your computer. You will be required to mount the drive inside your computer, connect signal and power cables to the hard drive, and update the configuration information. Handling precautions -------------------- 01 Turn off all attached devices first; then turn off the computer. 02 Unplug all the power cords from electrical outlets before starting installation. 03 Disconnect all power cables from your computer and attached devices before starting installation. 04 Limit your movement. Movement can cause static electricity to build up around you. 05 Handle the drive carefully and by the edges. 06 Do not touch any exposed printed circuitry. 07 Prevent other people from touching the components or the drive. 08 When you are installing the drive, touch the static-protective package containing the drive to a metal expansion-slot screw or other unpainted metal surface on the computer, for at least 2 seconds. (This drains static electricity from the package and your body.) 09 When possible, remove the drive and install it directly into the computer without setting it down. If this is not possible, place the drive, component side up, on the static-protective bag on a flat surface until the drive is installed. 10 Do not place the drive on the computer cover or on a metal table. Note: Be sure to use the correct screws provided with your drive. Using the wrong ones might cause damage to the drive. Completing the installation procedure ------------------------------------- The installation of the drive is complete. Reinstall the cover on the computer or storage enclosure. Store these instructions and any extra parts in a safe place in case you change your configuration. After installing your hard disk drive, use the information that came with your computer to reconfigure your system. When you power on your system, turn on all attached devices first; then turn on the computer. If you have any problems at this point, turn off all attached devices; then, turn off the computer and check that: 1 The cables are installed correctly 2 No options or cables are loose 3 The jumpers are properly set Turn on all attached devices; then, turn on the computer. If you still have a problem, refer to the troubleshooting information in the documentation that came with your computer. Update configuration -------------------- Whenever you add or remove an option from your computer, you must update the configuration information. Your computer might have an automatic configuration program, or you might have to follow a specific procedure. For more information, refer to the documentation that came with your computer. Preparing the drive for use --------------------------- Having successfully installed the hard disk drive, you need to prepare it for use. Depending on the operating system you are using, you might need to partition then format the hard disk. Refer to the documentation that came with your operating system for information on how to format your new drive. To make the drive just installed your primary drive, you might need to create a new system partition on the drive. For information on creating a new system partition, refer to the documentation that came with your operating system. Troubleshooting --------------- You might be able to solve a problem yourself. Before calling IBM, you might want to try some or all of the following troubleshooting procedures. 1 Remove and reattach all drive cables 2 Remove and reseat the drive 3 Place the drive in a different slot, if one is available 4 If your drive contains jumpers or switches, check that they are set as specified 5 Reread any software instructions; be sure software settings are correct 6 Inspect the drive for damage, such as bent pins 7 Check the computer manual for instructions about the installation of upgrades. Look for a section about system setup or system configuration. Follow all procedures. 8 After completing these steps, reassemble the computer and connect the power cord If you are still having problems and want to call IBM technical support, have available as much of the following information as possible: 1 Drive model or P/N and description 2 Computer manufacturer and model 3 Exact wording of error message (if any) 4 Description of the problem 5 Hardware and software configuration information for your system If possible, be at your computer. Your technical support rep might want to walk you through the problem during the call.