R Z 2 9 V A AVASTOR NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/HH Cylinders 3832| | | Capacity form/unform 4300/ 4901 MB Heads 20| | | Seek time / track 9.0/ 0.8 ms Sector/track | | | Controller SCSI2 SI/FAST Precompensation Cache/Buffer 2048 KB SEGMENTED Landing Zone Data transfer rate 4.400 MB/S int Bytes/Sector 512 10.000 MB/S ext SYNC Recording method RLL 1/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C | Power: sleep W Humidity % | standby W Altitude km | idle W Shock g | seek 13.0 W Rotation RPM 7200 read/write 15.0 W Acoustic dBA spin-up W ECC Bit 198BIT REED SOLOMON,ON THE... MTBF h 800000 Warranty Month 60 Lift/Lock/Park YES Certificates CSA,UL1950,VDE ********************************************************************** L A Y O U T ********************************************************************** QUANTUM XP31070/32150/34300 8-BIT PRODUCT MANUAL 81-108333-01 4/1995 +---------------------------------------------------------+ | |XX | +-+J5 |XXI | +-+ |XXN | |XXT | |XXE | |XXR J1 | |XXF | |XXA | |XXC | *Fault LED |XXE |+-+ |XX || | |XX || | |XX || | | |+-+ |XX Power | *Busy LED |XX J2 +---------------------------------------------------------+ 50-pin SCSI Connector (8-bit) ----------------------------- +------------------------------------+ | Back View | | | +------------J1----------------J2----+ |+------------ ------------++-------+| ||oooooooooooooooooooooooo1||O O O O|| ||oooooooooooooooooooooooo2|| || |+-------------------------++-------+| +-----------SCSI-------------Power---+ + + +------------------------------------+ | Front View (Bezel End) | | | | Fault LED | +-+----------------------------------+ +-++----------+----------------------+ | ||ooo oooooo20 | + ||oooooooooo| + |+1---------J3 Option Busy LED Connector ********************************************************************** J U M P E R S ********************************************************************** QUANTUM XP31070/32150/34300 8-BIT PRODUCT MANUAL 81-108333-01 4/1995 Jumper Setting ============== TERMPWR 8-bit Drives -------------------- | | +--+ | |xx| | TERMPWR (8-bit Drives) |oo| | To configure the drive to provide +--+ | active termination, install a jumper --------------------------+ as shown. Else, remove the jumper. XXXXXXXXXXXXXXXXXXXXXXXXX J1 SCSI Connector Active Termination (8-bit Drives) --------------------------------- The drive can be configured to provide or not provide active termination. The drive location on the SCSI bus and the method used to terminate the SCSI bus (active termination or separate terminator) determines how to configure the active termination feature of the drive. NOTE Refer to your system or SCSI controller documentation regarding any specific recommendations regarding drive placement on the SCSI bus and SCSI bus termination. +------------------+------------------------------------------------+ |Drive installation|Active Termination Configuration | |location on SCSI | | |Bus | | +------------------+------------------------------------------------+ |Drive installed |If there is no separate bus terminator used at | |at end of bus |the SCSI bus end that contains the drive, | | |configured the drive to provide active | | |termination. | +------------------+------------------------------------------------+ |Drive installed |If a separate bus terminator IS used at the SCSI| |at end of bus |bus end that contains the drive, configure the | | |drive to NOT provide active termination. | +------------------+------------------------------------------------+ |Drive NOT |Configure the drive NOT to provide active | |installed at end |termination. | |of bus | | +------------------+------------------------------------------------+ SCSI ID 8-bit Drives -------------------- Each SCSI device on the bus must have a unique SCSI ID number assigned to it. The drive can be configured for SCSI ID numbers that range from 0 through 7. Set the SCSI ID for the drive at Option connector J3. +------------------20 |o o o o o o o o o| Option Connector |o o o o o o o o o o| +1------------------+ +----------+-----------------------+ | SCSI ID | Pins | | | 5-6 | 3-4 | 1-2 | +----------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | +----------+-------+-------+-------+ | 1 | OPEN | OPEN | CLOSED| +----------+-------+-------+-------+ | 2 | OPEN | CLOSED| OPEN | +----------+-------+-------+-------+ | 3 | OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+ | 4 | CLOSED| OPEN | OPEN | +----------+-------+-------+-------+ | 5 | CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+ | 6 | CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+ | 7 | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+ Configure the drive for remote (external) SCSI ID selection by removing the SCSI ID jumpers (if present) from the referenced SCSI ID pins. Then connect the leads from the external selection switch(es) to the referenced pins. Observe the following guidelines while doing so. - ID Bit 0, at Pin 1, is the Least Significant Bit (and has the lowest priority). - SCSI ID Bits 0, 1, and 2 (pins 1, 3, and 5, respectively) are active LOW signals. That is, the bit is a 1 if the corresponding remote switch is closed to ground. - Use pins 2, 4, and 6 as the associated ground returns for ID bits 0, 1, and 2, respectively. The ground returns can be used individually, or the ground returns of all three ID bits can be combined at pin 2, 4, or 6. Spindle Synchronization 8-bit Drives ------------------------------------ The drive supports synchronized spindle operation. Whether the drive operates as master or slave is determined by the contents of the RPL field in the Rigid Disk Geometry Page (04h) for the drive or the Auto field of the Quantum (vendor) Special Function Control Page (25h). The time interval between spindle synchronization checks is set using the Spindle Sync Check Interval byte of the Quantum (vendor) Special Function Control Page (25h) of the MODE SELECT command. Intervals of 5 to 60 minutes can be set. The drive always maintains local speed regulation when no reference signal is applied. When the drive operates as a master, it generates a spindle synchronization reference signal (SPINDL_SYNC_REF L). This reference signal is available as an output to other drives at Option connector pins 10 and 19 (pins 10 and 19 are connected together on the drive). When the drive operates as a slave, it looks for a spindle synchronization reference signal (SPINDL_SYNC_REF L) as an input from the master drive. The slave looks for this spindle synchronization input at either pin 10 or 19 on the Option connector (pins 10 and 19 are connected together in the drive). CAUTION All Atlas series drives can be connected for synchronized spindle operation. Models XP31070, XP32150 and XP34300 drives must not be used for synchronized spindle operation in conjunction with drives from different model series or unpredictable results might occur. For example, XP31070, XP32150 and XP34300 drives can be connected for spindle synchronization in the same system, but they must not include a synchronization connection to a Capella series disk drive (VP31110 or VP32210). NOTE When connecting multiple drives together for spindle synchronization, be sure to use proper cabling techniques to avoid ground loop problems. Attach the spindle synchronization (SPINDL_SYNC_REF L) connection and associated ground connection at the Option connector. Pin 19 is provided to permit the use of a 2-pin plug for the spindle sync connections. Pin 10 i sprovided as an alternate spindle synchronization connection to facilitate installations where a 10-pin header is used to connect several remote features. The ground return pins are 2, 4, 6 or 20. +------------------20 |* * * 0 o o o o *| Option Connector |o o o o o o o o o 0| * = LOGIC_GND L (Pins 2, 4, 6, 20) +1------------------+ 0 = SPINDL_SYNC_REF L (pins 10, 19) Write Protection 8-bit Drives ----------------------------- +------------------20 |o o o o o o o X o| Option Connector |o o o o o o o o X o| +1------------------+ To write protect the drive, install a jumper across Option connector pins 17 and 18. To disable write protection, remove the jumper. Spin Up Power On 8-bit Drives ----------------------------- +------------------20 |o o o o o X o o o| Option Connector |o o o o o o X o o o| +1------------------+ Atlas drives have three Spin-Up on Power On modes: - Option 1 Spin up occurs immediately when power is apploed - Option 2 Drive spin up occurs after a predetermined delay following power on. The delay is equal to a user-specified multiplier, multiplied by one plus the numerical SCSI ID of the drive. This will give a staggered spin-up in multiple-drive installations. - Option 3 Drive spin up is controlled by the START STOP UNIT command. For Option 1, immediate spin up power on, install the jumper across pins 13 and 14 of the Option connector. For Option 2, spin up after a delay, install the jumper across pins 13 and 14 of the Option connector. Set delay parameters in the MODE SELECT command, Quantum (Vendor) Special Function Control Page (25h). For Option 3, spin up controlled by the START STOP UNIT command, remove the jumper (if present) from across pins 13 and 14 of the Option connector. Remote Busy and Fault Displays 8-bit drives ------------------------------------------- Busy and Fault status of the drive can be monitired remotely by connecting remote (external) Busy and remote Fault display LEDs to the Option connector. Remote Busy LED --------------- Connect the cathode side of the remote Busy LED to pin 9, BSY_OUT L. Connect the anode side of the LED to pin 11, +5VDC OUT. Remote Fault LED ---------------- Connect the cathode side of the remote Fault LED to pin 7, FLT_OUT L. Connect the anode side of the LED to pin 11, +5VDC OUT. +------------------20 |o o o o o o o o o| Option Connector |o o o o o o o o o o| +1------------------+ | | +-- +5VDC OUT | +---- BSY_OUT L +------ FLT_OUT L ********************************************************************** I N S T A L L ********************************************************************** QUANTUM VP31110/32210 CAPELLA PRODUCT MANUAL 81-108335-01 4/1995 Notes on installation ===================== Drive mounting -------------- horizontally vertically +-----------------+ +--+ +--+ +------------------+ | | | +-----+ +-----+ | | | | | | | | | | | |+----------------+| +-+-----------------+-+ | | | | | | || || +---------------------+ | | | | | | || || | | | | | | || || | | | | | | || || +---------------------+ | +-----+ +-----+ | || || +-+-----------------+-+ +--+ +--+ || || | | || || | | || || +-----------------+ || || ++----------------++ You can mount the disk drive in any position. LR models mount in RAID storage subsystems. The drive (with bezel) attaches to the system bay and accept #6-32 screws. Screws should not exceed 0.25 inch (6.25 millimeters) in length, otherwise damage to the PCB may result. Combination Connector - 8-bit ------------------------------ +-----------------+-----------------------------------------------+ | Part Number | Vendor | +-----------------+-----------------------------------------------+ | 12-41254-01 | Quantum | +-----------------+-----------------------------------------------+ | 87711-502 | Berg Electronics (formerly Dupont Electronics)| +-----------------+-----------------------------------------------+ Includes 0.1-in pitch, 50-pin SCSI connector and 4-pin power connector. Combination Connector - 16-bit ------------------------------- +-----------------+-----------------------------------------------+ | Part Number | Vendor | +-----------------+-----------------------------------------------+ | 12-43123-01 | Quantum | +-----------------+-----------------------------------------------+ | 87360-0003 | Molex | +-----------------+-----------------------------------------------+ Includes 68-pin SCSI connector, 4-pin power connector, and a 2-mm pitch, 12-pin (2x6) Option connector. Option Connector - 8-bit ------------------------ +-----------------+-----------------------------------------------+ | Part Number | Vendor | +-----------------+-----------------------------------------------+ | 12-36484-08 | Quantum | +-----------------+-----------------------------------------------+ | 954339-01-10-15 | 3M | +-----------------+-----------------------------------------------+ | P92-300-204-6 | AMP, Inc. | +-----------------+-----------------------------------------------+ | 87049-2085 | Molex, Inc. | +-----------------+-----------------------------------------------+ A 2-mm pitch, 19-pin (2x10) keyed (missing pin) connector Secondary Option Connector - 16-bit ----------------------------------- +-----------------+-----------------------------------------------+ | Part Number | Vendor | +-----------------+-----------------------------------------------+ | 12-36484-09 | Quantum | +-----------------+-----------------------------------------------+ | P93-300-204-7 | AMP | +-----------------+-----------------------------------------------+ | 954339-01-07-15 | 3M | +-----------------+-----------------------------------------------+ A 2-mm pitch, 13-pin (2x7) keyed (missing pin) connector Shunt Jumper - All Models ------------------------- +-----------------+-----------------------------------------------+ | Part Number | Vendor | +-----------------+-----------------------------------------------+ | 12-36482-01 | Quantum | +-----------------+-----------------------------------------------+ | 86730-001 | Berg Electronics (formerly Dupont Electronics)| +-----------------+-----------------------------------------------+ | LPC-SPG | Honda | +-----------------+-----------------------------------------------+ A 2-mm pitch shunt for configuring termination characteristics RAID Connector - SCA Models --------------------------- +-----------------+-----------------------------------------------+ | Part Number | Vendor | +-----------------+-----------------------------------------------+ | 12-41319-01 | Quantum | +-----------------+-----------------------------------------------+ | SSC80-D01 | Specialty Electronics | +-----------------+-----------------------------------------------+ Champ 0.050 inch Series I 80-position plug DC Power and pin connector assignments -------------------------------------- +------------+ pin 1 +12 VDC | 4 3 2 1 | pin 2 +12 Volts Return GROUND +------------+ pin 3 + 5 Volts Return GROUND pin 4 + 5 VDC Mounting brackets may be required when installing the drive in a 5.25-inch form factor bay. We recommended using brackets supplied by Quantum Corporation to mount the drive. Otherwise, the drive's isolation characteristics could be compromised. A bracket kit including four screws is available from the Quantum Corp. The part number is 70-30695-01. CAUTION The placement of the drive in the computer system must permit sufficient air-flow to maintain drive environment temperature within 41*CF to 131*F (+5*C to +55*C) and maintain component surface temperatures below the maximums. CAUTION Screw-length must not exceed 0.25-inch (6.25 millimeters); or the drive may be damaged (#6-32).