D C A S - 3 4 3 3 0 U L T R A S T A R IBM Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 8120| | | Capacity form/unform 4330/ MB Heads 6| | | Seek time / track 14.0/ ms Sector/track | | | Controller SCSI3 SI/WI/ULTR/FA2 Precompensation Cache/Buffer 448 KB SEGMENTED Landing Zone Data transfer rate 5.000 MB/S int Bytes/Sector 512 40.000 MB/S ext SYNC Recording method RLL 1/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 65 Power: sleep W Humidity % 8 90 | 5 95 standby W Altitude km | idle W Shock g 10 | 75 seek W Rotation RPM 5400 read/write W Acoustic dBA 37 spin-up W ECC Bit MTBF h 800000 Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** IBM DCAS-32160/34330 JUMPER SETTING +---------------------------------------------------------+ | +----------------- | | Pins 23,24++ |XXI | : | | |XXN | : | | |XXT | 1,2 +++ |XXE | | |XXR | | |XXF | | |XXA | | |XXC | | |XXE | | |XX | | |XX | Back Side of the Drive | |XX | | |XX Power | +------------------| +---------------------------------------------------------+ ********************************************************************** J U M P E R S ********************************************************************** IBM DCAS-32160/34330 JUMPER SETTING Jumper Setting ============== OPTION BLOCK Jumper Setting Jumper position and function are as shown below. Pin pitch is 2mm. +-------------- Disable Auto Spin Up Device ID | +--------- RESERVED +---+---+---+ | | +---- Unit attention Disable | | | | | | | +--------------- Enable TI-SDTR/WDTR | | | | | | | | +----------- Auto Start delay | | | | | | | | | +------- Delay start 6/12 | | | | | | | | | | +--- Disable SCSI Parity | | | | | | | | | | | JP1 JP2 JP3 JP4 JP5 JP6 JP7 JP8 JP9 JP10 JP11 +- LED Cathode +--++--++--++--++--++--++--++--++--++--++--++--+JP12 |24||22||20||18||16||14||12||10||08||06||04||02| +--++--++--++--++--++--++--++--++--++--++--++--+ +--++--++--++--++--++--++--++--++--++--++--++--+ |23||21||19||17||15||13||11||09||07||05||03||01| +--++--++--++--++--++--++--++--++--++--++--++-++ +----+---+---+---+---+---+---+---+---+---+ +- LED Anode Ground JP1 do not exist on 50 Pin models! +----------+-------------------------------+ | SCSI ID | Jumper Location | | | PINS | | | JP1 | JP2 | JP3 | JP4 | +----------+-------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | OPEN | +----------+-------+-------+-------+-------+ | 1 | OPEN | OPEN | OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 2 | OPEN | OPEN | CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 3 | OPEN | OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 4 | OPEN | CLOSED| OPEN | OPEN | +----------+-------+-------+-------+-------+ | 5 | OPEN | CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 6 | OPEN | CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 7 | OPEN | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 8 | CLOSED| OPEN | OPEN | OPEN | +----------+-------+-------+-------+-------+ | 9 | CLOSED| OPEN | OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 10 | CLOSED| OPEN | CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 11 | CLOSED| OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 12 | CLOSED| CLOSED| OPEN | OPEN | +----------+-------+-------+-------+-------+ | 13 | CLOSED| CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 14 | CLOSED| CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 15 | CLOSED| CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+-------+ 50-Pin (narrow SCSI) device have 8 possible addresses with address 7 (highest priority) normally reserved for the controller. SCSI ID 50 PIN Models --------------------- +----------+-----------------------+ | SCSI ID | Jumpers | | | JP2 | JP3 | JP4 | +----------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | +----------+-------+-------+-------+ | 1 | OPEN | OPEN | CLOSED| +----------+-------+-------+-------+ | 2 | OPEN | CLOSED| OPEN | +----------+-------+-------+-------+ | 3 | OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+ | 4 | CLOSED| OPEN | OPEN | +----------+-------+-------+-------+ | 5 | CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+ | 6 | CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+ | 7 | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+ ********************************************************************** I N S T A L L ********************************************************************** IBM DCAS-32160/34330 ULTRASTAR 2ES INSTALLATION GUIDELINES Notes on installation ===================== Installation direction ---------------------- horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ The drive will operate in all axis (6 directions). Mount the drive securely, using the appropriate brackets or rails, in any axis, using four 6-32 UNC metric screws in either bottom or side mounting holes. The max. screew insertion depth for the bottom mounting is 6.0mm (0.23 inch) and for side mounting 3.5 mm (0.14 inch).